When your old system quits in the middle of a Florida summer, you need AC installation Hunters creek FL that happens fast and holds up for years. We size, supply, and install Carrier, Trane, and Goodman systems for homes and small businesses across Orange County, and we pull the permits so the job is code-correct from day one. Call (844) 796-4282 and we will get your cool air back.
AC installation Hunters creek FL is the full replacement or first-time setup of a central cooling system, including the condenser, evaporator coil, line set, thermostat, and duct connections. We start with a Manual J load calculation to match tonnage to your square footage, then run new copper tubing, braze the joints, pull a deep vacuum with a vacuum pump, and charge the system with refrigerant R-410A or R-32 to the manufacturer's spec. Every install gets a NATE-certified tech on the final commissioning.
Most Hunters creek homes were built between the 1980s and early 2000s, and the original 10 SEER units are long past their useful life. If your system is 12 to 15 years old, runs all day, or uses R-22 refrigerant that is no longer produced, replacement usually costs less than another summer of repairs. We handle air conditioner installation Hunters creek for single-family homes, townhomes, and small commercial spaces, and we can often schedule same day AC installation Hunters creek when you call before noon.
Every install we do covers the equipment, the labor, the permit, and the startup. Here is what is in the standard scope, and what we quote separately if your home needs it. We tell you upfront which side of that line your job falls on.
Matched outdoor condenser and indoor evaporator coil from the same manufacturer, sized by Manual J load calculation. We verify the AHRI certification number so the system qualifies for the rated SEER2 efficiency and the full manufacturer warranty.
New copper tubing run from the condenser to the air handler, brazed with nitrogen purge, pressure tested, and pulled to 500 microns with a vacuum pump. We weigh in refrigerant R-410A or R-32 to the exact factory charge for your line length.
A new programmable or smart thermostat, wired and programmed. We install Nest and Ecobee on request and set up your schedule, geofencing, and temperature limits before we leave. Existing thermostats can be reused if they are compatible.
We pull the Florida HVAC contractor license permit through Orange County and meet the inspector on site. Any corrections flagged by the inspector are handled by us at no extra charge, and you get a closed permit when the job is done.
We reconnect the supply and return plenums, seal duct leakage at the boots and transitions with mastic and duct tape, and verify static pressure. If your existing ductwork is undersized for the new system, we quote that modification separately.
Final commissioning includes checking superheat and subcooling with manifold gauges, verifying temperature split, and testing the blower motor amp draw with a multimeter. We walk you through the filter location, thermostat settings, and warranty registration.
We measure square footage, count windows, check insulation and existing duct size, and inspect the electrical panel. This takes 45 to 60 minutes. You get a written load calculation and two or three equipment options at different price points.
You pick the brand and efficiency level. We stock Carrier, Trane, Lennox, Goodman, Rheem, York, Mitsubishi Electric, and Daikin, so we can usually match whatever you want. We confirm the AHRI certification number so you know the exact matched system going in.
We pull the Florida HVAC contractor license permit through Orange County and schedule the install. Most jobs are booked within 2 to 4 business days, and same-day slots open up when we have cancellations. You get a text with the crew's arrival window.
A two-person crew arrives with the condenser, coil, line set, and thermostat. Removal of the old unit takes about an hour. The new install runs 4 to 7 hours depending on attic access and duct modifications. We protect floors and clean up before we leave.
We pull a vacuum to 500 microns, weigh in the refrigerant charge, and verify static pressure and temperature split. Then we program your Nest or Ecobee thermostat, show you the filter location, and register the manufacturer warranty on the spot.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Used to read suction and liquid line pressures during charging. Accurate gauge readings are how we verify superheat and subcooling, which confirms the system has the exact refrigerant charge it needs.
Pulls the system down to 500 microns before charging. Skipping this step leaves moisture in the line set, which forms acid, destroys the compressor, and voids the manufacturer warranty.
Removes refrigerant from the old system before we disconnect it. Required by EPA Section 608 rules and the only legal way to handle R-22 and R-410A during a replacement.
The multimeter checks capacitor microfarads, contactor voltage, and blower motor amp draw. The combustion analyzer verifies safe operation on gas furnaces when we are replacing a matched system.
Used to cut and form copper tubing for the new line set. Clean cuts and proper flares prevent leaks at the connections, which is where most refrigerant loss starts.
Runs a rotating brush and negative pressure vacuum through the duct runs before we commission a new system. Clean ducts mean the new equipment is not fighting a layer of dust and debris from day one.
Original 10 SEER condenser running on R-22, compressor failed in July. Indoor temps hit 84 degrees, and the homeowner was quoted $1,800 just to replace the compressor on a 26-year-old unit.
We installed a matched 14.3 SEER2 Carrier system with a new coil, line set, and Nest thermostat. Indoor temp held at 74 degrees on a 96 degree day. Electric bill dropped from $265 to $185 the following month.
Upstairs bedrooms ran 6 degrees warmer than downstairs all summer. The existing 4-ton system short cycled, and the homeowner was ready to replace it with another 4-ton unit.
Manual J showed the home needed 3 tons, not 4. We installed a 3-ton variable-speed Trane system, sealed duct leakage at three supply boots, and added a return. Temperature split between floors dropped to 2 degrees.
Tenant reported warm air in early June. Diagnosis found a failed capacitor and a refrigerant leak at the evaporator coil on a 13-year-old Goodman system. Repair cost was close to half of replacement.
We replaced the system with a new Goodman 14.3 SEER2 condenser and matched coil, completed the install in 6 hours, and had the tenant cooling again the same day. Permit was pulled and closed within a week.
If your system is showing any of these symptoms, a repair might buy you a season. A replacement buys you a decade. Here is what we see most often on Hunters creek service calls, and how a new install fixes it for good.
Ask a pro →We diagnose the cause first, whether it is a refrigerant leak, a failing compressor, or a clogged evaporator coil. If the system is over 12 years old and the repair cost is more than a third of replacement, we quote a new install with a load calculation to size it right.
We leak-test the entire system with an electronic detector and nitrogen pressure test. If the leak is in the evaporator coil and the system is near end of life, replacement is usually the better call. A new system comes with a factory-sealed coil and a fresh warranty.
We run a Manual J load calculation to find the correct tonnage, then match the system to your actual square footage, window load, and insulation. Correctly sized equipment runs longer cycles, removes more humidity, and lasts years longer than an oversized unit.
We replace the full system with a modern R-410A or R-32 unit, which typically runs at 14.3 SEER2 or higher. You get lower bills, better humidity control, and a warranty that covers the whole system instead of just the part that failed.
Typical 2026 pricing for a full central AC replacement in Hunters creek runs $4,800 to $9,500 installed, depending on tonnage, SEER2 rating, and whether ductwork needs modification. A single-zone mini-split starts around $3,200. We give you a written quote after the in-home assessment, and financing is available for qualified buyers.
Most residential installs take 4 to 7 hours from arrival to commissioning. That includes removing the old condenser and coil, running new line set, and charging the system. If we are adding ductwork or upgrading the electrical panel, plan for a full day or a two-day job. We confirm the timeline when we book.
We size by Manual J load calculation, not rules of thumb. A 1,500 square foot home in Orange County typically needs a 2.5 to 3 ton unit, but ceiling height, window count, insulation, and duct condition all shift that number. Oversizing is the most common mistake we see, and it causes short cycling and poor humidity control.
Yes. We offer approved financing through third-party lenders with terms from 12 to 84 months, including 0 percent promotional plans for qualified buyers. You can apply online or on the tablet when the tech is at your home, and most decisions come back the same day. Ask about affordable AC installation in Hunters creek options when you call.
furnace repairFlorida winters are mild, but a furnace that quits in January still leaves you cold. We repair gas and electric furnaces across Hunters creek, and if you are already replacing your AC, we can inspect the furnace and heat exchanger while we are on site.Explore →
air conditioning repairNot every problem needs a new system. If your AC is not cooling but the compressor is under 10 years old, we diagnose refrigerant leaks, faulty thermostats, and blower motor failures first. Repair is often the smarter call before you commit to replacement.Explore →
furnace replacementWhen your furnace is past 15 years or the heat exchanger is cracked, replacement is the safe move. We install matched furnace and AC systems so both pieces communicate through the same thermostat and share the same warranty timeline.Explore →
air duct cleaningNew equipment pushing air through dirty ducts defeats the purpose. We clean supply and return runs, sanitize the plenum, and seal duct leakage before or right after a new install so your system moves the CFM it was rated for.Explore →
heating repairHeat pump and furnace problems show up fast when the temperature drops. We repair ignition failures, reversing valves, and defrost boards on heating systems across Hunters creek, usually the same day you call.Explore →
heat pump repairHeat pumps handle both heating and cooling, which means twice the parts that can fail. We service all major brands, including Mitsubishi Electric and Daikin, and we stock common capacitors and contactors on the truck.Explore →
emergency HVAC repairWhen your system dies at 10 p.m. in July, you need someone who answers. We run 24/7 emergency dispatch for Hunters creek and surrounding areas, with a live person on the phone and a tech rolling within the hour.Explore →
AC repairRefrigerant leaks, clogged air filters, dirty evaporator coils, and failed capacitors are the four most common AC repair calls we run. Most are fixed in a single visit, and we always check the whole system, not just the part that failed.Explore →We are licensed, insured, and backed by a 5-year workmanship warranty on every install. Call (844) 796-4282 now and we will give you a straight answer on timing, pricing, and which system fits your home. Same-day slots go fast in summer.
Book My Install (844) 796-4282 →Call (844) 796-4282 any time, day or night. A live dispatcher answers, takes your address and symptoms, and gives you an arrival window. For non-emergency work, we schedule same-day and next-day slots across Hunters creek and the surrounding neighborhoods, and we text you when the technician is on the way.